The Basics of Plumbing Skills for Bathtub Installation
The Basics of Plumbing Skills for Bathtub Installation
Blog Article
We have noticed this article on Installing A Bathtub down the page on the web and accepted it made good sense to talk about it with you on this page.
Setting up a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is likewise a moderately challenging task. If the old tub is easily accessible, the job can relocate quickly; if you need to open up a wall surface to remove the old tub and also place the new bathtub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will need a helper to leave the old bathtub as well as embeded in the brand-new one. See to it you have actually certified on your own for the task as well as fit trying it. Rather than working with a service provider to take control of a halfway-completed task, it is better to consider utilizing one prior to you begin. Chances are you may require a professional plumber to make tube connections.
This article will certainly assist you install a brand-new tub in your restroom if you have actually currently bought a brand-new tub and also don't require to change the setup of your previous water system pipelines.
Your tools and also material list must make up the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is disconnect the water supply. After doing so, switch on the faucets to drain any kind of water remaining in the system. The process of getting rid of the existing taps can be rather bothersome due to the restricted gain access to that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a towel ready for the staying water that will certainly originate from the pipelines. Once the supply pipes have been eliminated, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning during this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old securing compound.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washing machines are in location between the tap and also the sink. Secure the tap in place with the supplier provided backnut. Once the tap is safely in position, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical faucet ports. The former kind needs to be connected to the tap ends first, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Mounting the Bath tub
Using both wood boards under its feet, place the bathtub in the called for setting. The wooden boards are useful in evenly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 little factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bath tub until the spirit level reviews level.
To set up faucets, fit all-time low of the furthest versatile faucet port to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other faucet.
Switch on the water supply and also examine all joints and also brand-new pipework for leakages and tighten them if needed. Fill the bathtub and likewise examine the overflow outlet and the normal outlet for leaks.
Ultimately, deal with the bath paneling as described in the maker's user's manual. Tiling as well as securing around the tub needs to wait until the bath tub has been used at the very least once as this will certainly settle it into its last setting.
Preparing for the Installment
To start with, the sustaining framework provided with the bathroom needs to be fitted (if called for) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the tap features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps device to prevent strain on the bath tub.
Fit the adaptable faucet ports to the bottom of both taps using 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to now prepare to be fitted in its last position.
Tiling Around the Tub
In the location where the bath meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack a rigid seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, causing difficulties with wetness and also feasible leaks to the ceiling below.
You can choose from a range of coloured sealants to assimilate your components and installations. They are offered in tubes as well as cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealant can break fairly early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water-proof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that piece on How to Install a Bathtub while surfing the internet. So long as you liked our blog post plz be sure to pass it around. We treasure reading our article about How to Install a Bathtub Yourself.
Book Today! Report this page